UV Technologies

Service & Spare Parts

service and support

  1. On-site service Australia wide (Hanova UV, Berson UV and Bran+Luebbe OLM)
  2. Factory trained service engineers
  3. 5 year manufacturer's warranty for Hanovia UV and Berson UV systems (excl consumables)**
  4. Local stocks of maintenance parts, critical spares and UV lamps
  5. UV lamps supported by manufacturer's  replacement warranty**
  6. We only stock GENUINE parts
  7. Service agreements and breakdown service available 

 Contact us on 02 4735 5054 or

 **subject to terms and conditions

Continuous, safe and efficient disinfection when you choose a UV system supplied by Fluidquip Australia.

5 Years Manufacturer's Warranty

  • Hanovia UV and Berson UV purchasers can take advantage of the manufacturer's free 5 year extended warranty . Excludes consumables and some conditions apply.

Factory Trained Service Engineers

  • Our investment in the factory training of our service engineers, saves you money and protects your investment. Our service engineer's experience and knowledge will keep your UV system operating as designed by the manufacturer.

Local Stocks of Critical Spares and UV Lamps

  • Fluidquip Australia holds local stocks of all critical spares and common UV lamps, ensuring a speedy response in the unlikely event of a breakdown.

Australia-Wide, On-Site Servicing

  • We supply scheduled  and emergency on-site service Australia-wide using our factory trained service engineers.
  • Service Agreements available for set-and-forget servicing. Our Service Agreements  schedule annual preventative maintenance visits , the replacement of consumables at the correct intervals and the monitoring of all aspects of your UV system for maximum performance and early identification of wearing parts.

GENUINE UV Lamps with Replacement Warranty

  • We supply only genuine replacement UV lamps for Berson UV and Hanovia UV systems.
  • Genuine lamps are designed for maximum resilience, with all lamps certified and traceable to national standards.
  • All our replacement lamps come with a full replacement warranty if they fail in under 1000 hours, and a pro-rata warranty if they fail under 8000 hours (medium pressure lamps with initial output below 70%) or 14000 hours (for low pressure amalgam lamps)

Manufacturer DVGW Sensor Recalibration

  • Manufacturers recommend the annual re-calibration and preventative maintenance care of your UV Monitor.
  • Annual re-calibration by the manufacturer is essential if your water business needs to comply with industry validation standards.
  • Annual re-calibration will give you confidence that your Sensors will continue to work accurately maintaining your UV system efficiency.
  • Fluidquip Australia send all Sensors to the manufacturer for factory recalibration and maintenance.

Training and Education

  • Whilst the Hanovia UV and Berson UV systems are known for their ease of use, if you are a company managing multiple UV systems you may prefer to have in-house expertise. We can supply training for all your staff in UV principles as well as the maintenance and management of these systems. Link to more information about Training and Education in UV Systems

 

 

Contact us on 02 4735 5054 or

Exclusive Authorised distributor

  • Fluidquip Australia is the EXCLUSIVE AUTHORISED distributor for Bran+Luebbe On-line Monitors .
  • We are the only source of GENUINE and original parts and consumables

Factory Trained Service Engineers

  • With over 20 years experience servicing Bran+Luebbe On-Line Monitors our factory trained service engineers are the right people to keep your On-Line Monitors performing optimally.

Australia-Wide, On-site Servicing

  • We offer on-site servicing, Annual Service Agreements and breakdown servicing Australia-wide.
  • Annual service agreements provide scheduled on-site preventative maintenance, monitoring of wearing parts, and priority breakdown options.

Local Stocks of GENUINE Parts and Consumables

  • We hold local stocks of all commonly used Pump Tubes, Dosing Hoses, other consumables and maintenance parts.
  • We offer a set-and-forget service for Pump Tubes and Dosing Hoses: we will deliver your consumables to your door at scheduled intervals according to your User Manual servicing requirements. No extra charges apply, but peace of mind is guaranteed!
  • Refer to the table below for common part numbers for Dosing Hoses and Pump Tubes

Bran+Luebbe On-Line Monitor Reagents

  • We supply all reagents for Bran+Luebbe On-line Monitors. See below for the most commonly used online monitor reagents. Contact us if the reagent you require is not listed here.
  • We offer a set-and-forget service for On-line Monitor reagents: we will deliver your reagents direct to your door at scheduled intervals according to your usage requirements. No extra charges apply, and guaranteed to make your life easier- one less task for you to remember to do!

Contact us on 02 4735 5054

 

Commonly Used On-line Monitor Dosing Hoses and Pump Tubes

Description Part Number Use
D48PP Dosing Hose 849355 Pump assembly dosing hose for peristaltic pump
D08 Dosing Hose 849390 Pump assembly dosing hose for peristaltic pump
D16 Dosing Hose 849391  Pump assembly dosing hose for peristaltic pump
D24 Dosing Hose 849392 Pump assembly dosing hose for peristaltic pump
D32 Dosing Hose 849393  Pump assembly dosing hose for peristaltic pump 
D40 Dosing Hose 849394  Pump assembly dosing hose for peristaltic pump
D48 Dosing Hose 849395 Pump assembly dosing hose for peristaltic pump
D64 Dosing Hose 849396 Pump assembly dosing hose for peristaltic pump 
Orange/Yellow Pump Tube 120+2100-05 Pump Tube
Orange/Orange Pump Tube 120+2100-08  Pump Tube
Red/Red Pump Tube 120+2100-10 Pump Tube
Yellow/Yellow Pump Tube 120+2100-12 Pump Tube
 Violet/ Violet Pump Tube 120+2100-15 Pump Tube
Violet/ Orange Pump Tube 120+2100-17  Pump Tube

Other Parts

 

Description Part Number Use
White Clamp Tube 515-9012-01 Platten used for multi-speed pump
Clamping Device 811935 3 roller pump tube bed
Tygon Tubing 562-0001-01  
Tygon Tubing 562-0003-01  
Tygon Tubing 562-0007-01  
Tygon Tubing 562-0020-01  
Tygon Tubing 562-0109-01  

Commonly Used Reagents

Part Number  Description  Pack Size
130+R000 Water Deionised  5 Litre
130+R0102 Molybdate Solution 5 Litre
130+R0103 Reductant Solution 5 Litre
130+R0121 Calibration Solution 5 Litre
130+R0191 Acid Solution  5 Litre
130+R1401 Reagent Buffer 5 Litre
130+R1422 Reagent Calibration Solution 0.020 mg/L Na  5 Litre
130+R1423 Reagent Calibration Solution 0.80mg/L Na 5 Litre
130+R3401 Reductant Solution  5 Litre
130+R3402 Formaldoxime 5 Litre
130+R3421 Calibration Solution 5 Litre

130+R3491

Buffer 5 Litre
130+R3492 Mask Solution 5 Litre
780115 Sulphuric Solution 5 Litre
780127 Reduction Solution (708127) 5 Litre
780209 TPTZ Solution  5 Litre
780293 Molybdate Reagent 5 Litre
780294 Reducing Solution 5 Litre
780562 Calibration Solution 150 ppb SiO2 5 Litre
780771 Calibration Solution 5 Litre
780956 Calibration Solution 0.15mg/L Mn 5 Litre
IR050 Synermed Chloride Reagent 500ml 500 ml
781258    
781257    
781252    
781253    
781254    
781255    
781256    
781075    
781083    
781085    
781084    


 

 

 Contact us on 02 4735 5054 or

With Partech's emphasis on accuracy and reliability you may not ever have the need to contact us for service. In the unlikely event of a breakdown you'll be pleased to know that we can provide you a prompt and reliable service.

Return to Base Service

  • Should you need servicing or repairs you can send your Partech sensor or monitor to our Sydney workshops. 
  • Fluidquip Australia Pty Ltd, Unit 7/ 84-90 Old Bathurst Rd, Emu Plains, NSW, 2750
  • Ensure you enclose your contact details, description of the problem and return address

Qualified Service Engineers

  • Our service engineers have over 10 years experience distributing and servicing Partech sensors and water quality monitors.

Genuine Replacement Parts

  • We use only genuine Partech replacement parts

 

Contact us on 02 4735 5054 or

Return to Base Service

  • Should you need servicing or repairs you can send your RealTech UVT  to our Sydney workshops. 
  • Fluidquip Australia Pty Ltd, Unit 7/ 84-90 Old Bathurst Rd, Emu Plains, NSW, 2750
  • Ensure you enclose your contact details, description of the problem and return address

Qualified Service Engineers

  • Your service work is carried out by our on-staff qualified service engineers

Genuine Replacement Parts

  • We use only genuine RealTech replacement parts.

Contact us on 02 4735 5054 or

website design © 2009 stralia web
Experience BlueMountainsAustralia.com
website content © 2009 Fluidquip Australia